View MC10E175_88353.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
9 Bit Latch With Parity
The MC10E/100E175 is a 9-bit latch. It also features a tenth latched output, ODDPAR, which is formed as the odd parity of the nine data inputs (ODDPAR is HIGH if an odd number of the inputs are HIGH). The E175 can also be used to generate byte parity by using D8 as the parity-type select (L = even parity, H = odd parity), and using ODDPAR as the byte parity output. The LEN pin latches the data when asserted with a logical high and makes the latch transparent when placed at a logic low level.
MC10E175 MC100E175
9-BIT LATCH WITH PARITY
* * * * * *
9-Bit Latch Parity Detection/Generation 800ps Max. D to Output Reset Extended 100E VEE Range of - 4.2V to - 5.46V Internal 75k Input Pulldown Resistors
Pinout: 28-Lead PLCC (Top View)
D6 25 D5 D4 D3 VEE LEN MR D2 26 27 28 1 2 3 4 5 D1 6 D0 7 VCCO 8 ODDPAR 9 Q0 10 VCCO 11 Q1 D8 D7 24 D8 23 VCCO 22 Q8 21 Q7 20 VCCO 19 18 17 16 15 14 13 12 Q6 Q5 VCC Q4 Q3 VCCO Q2 D0
FN SUFFIX PLASTIC PACKAGE CASE 776-02
LOGIC DIAGRAM
Q R Q0
D EN
BITS 1-7 D EN R Q Q8
* All VCC and VCCO pins are tied together on the die.
PIN NAMES
Pin D0 - D8 LEN MR Q0 - Q8 ODDPAR Data Inputs Latch Enable Master Reset Data Outputs Parity Output Function D EN R LEN MR Q ODDPAR
12/93
(c) Motorola, Inc. 1996
2-1
REV 2
MC10E175 MC100E175
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol IIH IEE Characteristic Input HIGH Current Power Supply Current 10E 100E 110 110 min typ max 150 132 132 110 110 min 25C typ max 150 132 132 110 127 min 85C typ max 150 132 152 Unit A mA Cond
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol tPLH tPHL Characteristic Propagation Delay to Output D to Q D to ODDPAR LEN to Q LEN to ODDPAR MR to Q(tPHL) MR to ODDPAR(tPHL) Setup Time D (Q) D (ODDPAR) Hold Time D (Q) D (ODDPAR) Reset Recovery Time Within-Device Skew LEN, MR D to Q D to ODDPAR Rise/Fall Times 20 - 80% 300 min 450 850 525 525 525 525 275 900 175 - 300 850 typ 600 1150 700 700 700 700 100 700 -100 - 70 600 75 75 200 500 800 300 max 800 1450 900 900 900 900 min 450 850 525 525 525 525 275 900 175 - 300 850 600 75 75 200 500 800 300 25C typ 600 1150 700 700 700 700 max 800 1450 900 900 900 900 min 450 850 525 525 525 525 275 900 ps 175 - 300 850 600 75 75 200 ps 500 800 ps ps 1 85C typ 600 1150 700 700 700 700 max 800 1450 900 900 900 900 ps Unit ps Cond
ts
th
tRR tSKEW
tr tf
1. Within-device skew is defined as identical transitions on similar paths through a device.
FUNCTION TABLE
D H L X X EN L L H X MR L L L H Q H L Q0 L ODDPAR H if odd no. of Dn HIGH H if odd no. of Dn HIGH Q0 L
MOTOROLA
2-2
ECLinPS and ECLinPS Lite DL140 -- Rev 4
MC10E175 MC100E175
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
0.007 (0.180) U T L -M
M
B -NY BRK
M
S
N
S S
0.007 (0.180)
T L -M
N
S
D Z -L-M-
W
28 1
D X VIEW D-D G1 0.010 (0.250)
S
V
T L -M
S
N
S
A Z R
0.007 (0.180) 0.007 (0.180)
M
T L -M T L -M
S
N N
S
H
S
0.007 (0.180)
M
T L -M
S
N
S
M
S
C
E G G1 0.010 (0.250)
S
K1 0.004 (0.100) J -TSEATING PLANE
K F VIEW S 0.007 (0.180)
M
VIEW S T L -M
S
T L -M
S
N
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 -- 0.025 -- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 -- 0.020 2 10 0.410 0.430 0.040 --
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 -- 0.64 -- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 -- 0.50 2 10 10.42 10.92 1.02 --
ECLinPS and ECLinPS Lite DL140 -- Rev 4
2-3
MOTOROLA
MC10E175 MC100E175
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-4
*MC10E175/D*
MC10E175/D ECLinPS and ECLinPS Lite DL140 -- Rev 4

▲Up To Search▲

Price & Availability of MC10E175

	To Download MC10E175 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .